Famco Chimney Sweep Nationwide

Famco Chimney Sweep in Marietta: What to Know First

We sweep and service Famco chimney systems in Marietta as an independent provider, not a Famco-authorized dealer, and most standard jobs are completed within a single visit. A routine Famco chimney sweep in Marietta typically runs $189 to $289 before any repairs, and you’ll get a written price before we start, so there’s no surprise at the end of the job. If you own a home in Marietta with a Famco chimney, fireplace, or stove system, this page covers what actually goes wrong with them, what it costs to fix, and what our guarantee does and doesn’t cover. Call (229) 350-8952 for a free estimate.

Call (229) 350-8952

How Famco Products Fail – and How We Fix Them

Famco builds solid residential chimney systems, but after a decade of sweeping them in Marietta, we know exactly where they wear. Here are the failure modes we see most:

• Famco stainless steel liners with locked-in creosote rings. On Famco rigid and flexible stainless liners, especially the ones installed in older Cobb County homes, we see hard creosote that forms in the corrugations and can’t be removed with a standard brush alone. We use a rotary chain whip with poly brushes to break those rings loose without gouging the liner. A smooth liner surface after the sweep is the difference between a clean chimney and a future chimney fire.
• Famco caps and rain pans with rust-through at the seams. The galvanized components on Famco termination caps hold up fine in dry climates, but Marietta’s humidity and summer thunderstorms accelerate corrosion at the seams. When a customer reports water dripping into the firebox after heavy rain, we find rust perforation in the cap pan about seven times out of ten. We replace with stainless, not galvanized, because the next cap should outlast the roof.
• Famco wood stove adapters with warped connector rings. On Famco stove systems, the single-wall connector pipe and stove collar see direct heat stress. We’ve pulled connectors in Marietta that have warped enough to break the seal at the thimble. The symptom is smoke smell in the room on cold starts, even when the chimney itself is clean. We check every connector joint for proper male-end-down orientation and replace warped sections with the correct gauge.
• Famco masonry rebuilds with failing mortar joints. Famco rebuild kits and masonry components used on historic Marietta chimneys, especially along Kennesaw Avenue near the Square, have a common issue: the mortar used during the original install was mixed too rich, and after a few freeze-thaw cycles, the joints start spalling. We remove and repoint with a softer, breathable mortar matched to the original brick’s age and hardness. Too many sweeps use modern Type S mortar, which is harder than the brick and causes the brick to crack instead of the joint.
• Famco zero-clearance fireplaces with baffle deterioration. On Famco prefab fireplaces, the ceramic fiber baffles above the firebox are a known wear item. By the time a Marietta homeowner notices the fireplace drawing poorly or soot staining above the opening, the baffle is usually cracked or sagging. We inspect baffles on every sweep, and when we replace them, we use the correct OEM-spec material, not a box-store substitute that changes the fireplace’s burn characteristics.

Our Famco Chimney Sweep Process

Here’s what a Famco chimney sweep in Marietta looks like when you call Alcott Chimney Marietta:

1. 1
   You call and a live person answers. Any time, day or night. You’ll tell us what you’re seeing – smoke backing up, soot smell, water marks – and we’ll schedule the sweep. You’ll get the technician’s name and photo before we arrive.
2. 2
   We verify who we are at your door. The technician shows a photo ID badge, matches the name and face you received, and is in uniform. No exceptions. This is the Threshold Standard, and it applies to every visit.
3. 3
   The technician examines your Famco system end to end. We check the cap or crown, the liner, the smoke chamber if it’s a masonry chimney, the damper, the firebox, the hearth, and the clearances. Any creosote buildup, glazing, animal debris, or water damage gets documented. You’ll see photos of anything we find, so when we say a part is bad, you can see it with your own eyes.
4. 4
   We give you a written price before any work begins. The sweep is a flat rate. If we find something that needs repair, you get a line-item quote with real dollar ranges. Nothing is hidden, and nothing is “discovered” after the fact. If the chimney only needs a sweep, that’s all we do, and we’ll tell you plainly when other work can safely wait.
5. 5
   We sweep the system completely. That means drop cloths, a sealed vacuum, and a thorough clean of the entire flue from the termination down to the firebox. We don’t do the “quick brush and go” job. We clean the smoke shelf, the damper assembly, and the firebox floor. When we’re done, the system pulls air like it should.
6. 6
   We walk you through what we found and what we did. You get a straight explanation of what was dirty, why it happened, and how to keep it from happening again. Every repair we make carries a written guarantee. If the repair fails within the coverage period, the second visit is free. That’s the 365-Day Done Right Promise, and it’s included on every job – not sold as an add-on.

What Famco Chimney Sweep Costs in Marietta

Here are the real numbers for common Famco scenarios in Marietta:

• Standard Famco chimney sweep: $189 to $289, depending on the height of the flue, the type of liner (rigid vs. flexible), and the amount of creosote buildup. Most single-story Marietta homes with a typical Famco stainless liner fall right around $220.
• Sweep plus Level 2 video inspection: $340 to $450. We run a camera through the flue after the sweep, and you get a copy of the video file. If you’re buying a home in Marietta with a Famco system, this is the inspection we recommend.
• Creosote removal with rotary treatment: $250 to $400, when standard brushing can’t break loose glazed or third-degree creosote. This usually applies to Famco liners on wood-burning systems that haven’t been swept in three or more years.
• Famco cap replacement: $180 to $350 installed, depending on whether we’re replacing a galvanized cap with stainless or matching an unusual size on an older Famco termination.

What moves the price: the system’s height, how long it’s been since the last sweep, and whether the cap or any components need parts. One thing that never moves the price once we’ve quoted it: the price itself. You approve a written number before we touch anything. Call (229) 350-8952 and we’ll give you a free estimate for your specific Famco setup.

Why Marietta Homeowners Call Alcott Chimney Marietta for Famco Work

We’ve been serving Marietta homeowners since 2002 as part of the Threshold Group family of home-service companies, and the reason people keep calling us back is simple: we show our work. You’ll know exactly who’s coming to your door before we arrive, because every technician is background-checked, identity-verified, and sent to you by name and photo. That’s the Threshold Standard, and it’s non-negotiable on every single visit. Ruben Castellano has spent well over a decade focused on chimney cleaning and inspection in this area, and he’s become the guy Marietta neighbors call when they want a straight answer instead of a scare tactic. On Famco jobs specifically, we install and service the professional trade materials that chimney pros actually specify – DuraFlex liner systems, HeatShield resurfacing, Gelco, Olympia Chimney, Famco, and Copperfield – so if your Famco system needs a component that works with what’s already there, we’re not improvising with box-store parts. And every job carries a written guarantee. If our repair fails within the coverage period, we come back and make it right for free. No fine print, no upsell. Tell me what you’re seeing and I’ll tell you exactly what it means – no guesswork, no upsell.

FAQs